We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
Writing in the journal Polymers, a team of scientists from Victor Babeș University of Medicine and Pharmacy Timișoara, Politehnica University Timişoara, and the National Institute for Research and Development in Electrochemistry and Condensed Matter in Romania have collaborated on a paper investigating the surface properties, color stability, and microhardness of PEEK for dental applications.
Study: Surface Characteristics and Color Stability of Dental PEEK Related to Water Saturation and Thermal Cycling . Image Credit: Olena Yakobchuk/Shutterstock.com
Advanced materials research has been central to the field of dentistry in the past few decades. Materials have been investigated for use in partial denture applications, with the most common materials employed for this purpose being metal alloys. Alloys possess the benefits of high strength and adequate friction and retention, but they can be hindered by corrosion instability.
Problems can occur with partial dentures, such as allergic reactions and topical disorders due to their direct contact with the oral mucosa. Moreover, they can be limited in terms of their aesthetics, as metal clasps can be visible on the buccal sides of molars.
Polyetheretherketone (PEEK) is a high-performance polymer that has been explored in recent years as a material for partial denture applications. Research has indicated that this polymer can address the issues with conventional metal alloys in prosthetic applications.
PEEK has been used extensively in orthopedic surgery and has increasingly found applications in prosthetic dentistry. This white, rigid, and radiolucent material possesses good thermal stability and mechanical properties, is biocompatible, non-toxic, and resistant to hydrolysis. Moreover, it possesses a low affinity for plaque and is non-allergic.
Weight variations of the samples during water immersion periods and thermocycling: average weight values with SD. Image Credit: Porojan, L et al., Polymers
Despite its good fracture resistance, however, this polymer is mechanically weak in its homogenous form. Dental clasps constructed from this material are weaker than their metal alloy counterparts. To overcome strength issues, composites of PEEK and materials such as ceramic fillers have been developed.
The aesthetic properties of these composites can be enhanced and provide benefits over traditional prosthetic materials for patients with high aesthetic requirements and can reduce allergic reactions. Likewise, surface modifications such as polishing of these composites can decrease or increase discoloration vulnerability in prosthetics, with rougher surfaces more likely to stain. Additionally, surface roughness can cause discomfort to patients.
Due to the importance and potential of PEEK and PEEK composites for prosthetic dentistry, a thorough characterization of their properties and an understanding of the long-term performance of these materials is needed in the field of dental science.
The paper in the journal Polymers has sought to elucidate the color stability, surface characteristics, and microhardness of PEEK materials in relation to in vitro aging and water saturation. Custom modified and unmodified samples of varied materials were evaluated in the research.
The materials studied were BioHPP, Juvora Medical PEEK, and Finoframe PEEK. All three materials are commercially available products used in the field of prosthetic dentistry. BioHPP is a composite reinforced PEEK/ceramic material, whereas the other two materials are constructed of 100% PEEK.
Forty-eight rectangular samples were prepared for evaluation. Prepared specimens were then immersed in distilled water for 28 days at 37 oC and then subjected to 10,000 thermal cycles to age them. After this process, the samples were analyzed using different methods.
A contact profilometer was employed to analyze the surface characteristics of the prepared samples. AFM was used to characterize the nanostructured topography of the materials. A micro-hardness tester was used to perform Vickers hardness measurements. The sample’s color changes were observed and calculated at regular weekly intervals.
3D reconstructions of AFM images. Image Credit: Porojan, L et al., Polymers
The results of the study demonstrated the performance of the different materials, revealing their suitability as dental prosthetic materials. Modified PEEK materials possess better qualities than their unmodified counterparts due to the presence of ceramic fillers.
After immersion for a week, all samples reached water saturation, with no notable difference between them. Microhardness is reduced by water saturation. The modified PEEK material was most affected by this. After thermocycling, microroughness was significantly increased. No notable differences between samples with respect to microroughness were observed.
After aging, the reinforced PEEK material displayed the least modification in terms of nanosurface roughness and topography. These properties were within clinical limits. Color changes after water immersion of four weeks and a year of simulated aging were within acceptable limits, varying from slight to extremely slight, demonstrating the suitability of PEEK-based prosthetic materials for aesthetic purposes.
Mean optical parameters values of the samples with SD before each week of water immersion (0), after (1–4), and after thermocycling: (a) TP, (b) CR, and (c) OP. Image Credit: Porojan, L et al., Polymers
The authors have stated that the study is limited by its narrow choice of materials and limited factors studied. Therefore, they have stated that future studies should investigate the aging behavior of this class of dental prosthetic materials by studying the complete oral environment.
Porojan, L et al. (2022) Surface Characteristics and Color Stability of Dental PEEK Related to Water Saturation and Thermal Cycling Polymers 14(11) 2144 [online] mdpi.com. Available at: https://www.mdpi.com/2073-4360/14/11/2144
Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.
Reg Davey is a freelance copywriter and editor based in Nottingham in the United Kingdom. Writing for News Medical represents the coming together of various interests and fields he has been interested and involved in over the years, including Microbiology, Biomedical Sciences, and Environmental Science.
Please use one of the following formats to cite this article in your essay, paper or report:
Davey, Reginald. (2022, May 26). Surface Properties of PEEK in Dental Applications. AZoM. Retrieved on July 29, 2022 from https://www.azom.com/news.aspx?newsID=59174.
Davey, Reginald. "Surface Properties of PEEK in Dental Applications". AZoM. 29 July 2022. <https://www.azom.com/news.aspx?newsID=59174>.
Davey, Reginald. "Surface Properties of PEEK in Dental Applications". AZoM. https://www.azom.com/news.aspx?newsID=59174. (accessed July 29, 2022).
Davey, Reginald. 2022. Surface Properties of PEEK in Dental Applications. AZoM, viewed 29 July 2022, https://www.azom.com/news.aspx?newsID=59174.
Do you have a review, update or anything you would like to add to this news story?
At the Advanced Materials Show 2022, AZoM caught up with the CEO of Cambridge Smart Plastics, Andrew Terentjev. In this interview, we discuss the company's novel technologies and how they could revolutionize how we think about plastics.
At the Advanced Materials Show in June 2022, AZoM spoke with Ben Melrose from International Syalons about the advanced materials market, Industry 4.0, and efforts to move toward net-zero.
At the Advanced Materials Show, AZoM spoke with Vig Sherrill from General Graphene about the future of graphene and how their novel production technique will lower costs to open up a whole new world of applications in the future.
Discover the OTT Parsivel², a laser disdrometer that can be used to measure all precipitation types. It allows users to collect data on the size and speed of falling particles.
Environics offers stand alone permeation systems that can be used for single or multiple disposable permeation tubes.
Grabner Instruments’ MiniFlash FPA Vision Autosampler is a 12-position autosampler. It is an automated accessory designed to be used with the MINIFLASH FP Vision Analyzer.
This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.
Corrosion is the degradation of an alloy caused by its exposure to the environment. Corrosion deterioration of metallic alloys exposed to the atmosphere or other adverse conditions is prevented using a variety of techniques.
Due to the ever-increasing demand for energy, the demand for nuclear fuel has also increased, which has further created a significant increase in the requirement for post-irradiation examination (PIE) techniques.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022